Difference between revisions of "Hydra"

From CSLabsWiki
Jump to: navigation, search
Line 22: Line 22:
  
 
=Install=
 
=Install=
 +
 +
Do a basic debian install with the hard drives software raided in RAID 6, all of the device as /, then continue below
 +
 +
==Install Packages==
  
 
<pre>
 
<pre>
 
apt install htop iotop iftop lm-sensors vim sudo qemu-kvm libvirt-bin virtinst screen rsync tmux
 
apt install htop iotop iftop lm-sensors vim sudo qemu-kvm libvirt-bin virtinst screen rsync tmux
 +
</pre>
 +
 +
==Network Configuration==
 +
 +
We beed to create a network bridge for the VM's to connect on.
 +
 +
<pre>
 +
/etc/network/interfaces
 +
</pre>
 +
 +
<pre>
 +
source /etc/network/interfaces.d/*
 +
 +
# The loopback network interface
 +
auto lo
 +
iface lo inet loopback
 +
 +
# Auto Configure eth0 and eth1 (our two NIC's - the ethernet over the usb ports is actually a IPMI port)
 +
auto eth0
 +
auto eth1
 +
 +
# Bridge, set the IP here and bridge all the defined ports for communication
 +
auto br0
 +
iface br0 inet static
 +
        address 128.153.145.42
 +
        netmask 255.255.254.0
 +
        gateway 128.153.144.1
 +
        bridge_ports all
 
</pre>
 
</pre>
  

Revision as of 10:44, 4 September 2016

Hydra
IP Address(es): 128.153.145.42
Contact Person: Jared Dunbar
Last Update: Fall 2016
Services: Various


Hostname: hydra.cslabs.clarkson.edu
Operating system: Debian 8.2
NIC 1: Clarkson Network
MAC: ?
IP: 128.153.145.42
CPU: 2x 16 Core AMD Opteron 6376
RAM: 4x 16GB DDR3-1600 ECC


Hydra is our newest VM host (as of September 2016

Install

Do a basic debian install with the hard drives software raided in RAID 6, all of the device as /, then continue below

Install Packages

apt install htop iotop iftop lm-sensors vim sudo qemu-kvm libvirt-bin virtinst screen rsync tmux

Network Configuration

We beed to create a network bridge for the VM's to connect on.

/etc/network/interfaces
source /etc/network/interfaces.d/*

# The loopback network interface
auto lo
iface lo inet loopback

# Auto Configure eth0 and eth1 (our two NIC's - the ethernet over the usb ports is actually a IPMI port)
auto eth0
auto eth1

# Bridge, set the IP here and bridge all the defined ports for communication
auto br0
iface br0 inet static
        address 128.153.145.42
        netmask 255.255.254.0
        gateway 128.153.144.1
        bridge_ports all

Hardware Information

IMPORTANT - DO NOT BUMP OR JOSTLE CASE

The CPU0 heat sink cooler is not very well mounted. It is mounted properly, however if the server is bumped too hard, the cooler will pop off. Treat the server with extreme care ALWAYS

  • 2x 16 Core AMD Opeteron 6376
  • 4x 16GB DDR3-1600 ECC RAM
  • 5x 2TB Segate Constelation HDD in RAID 6
  • 2x Noctua CPU Coolers
  • Super Micro MBD-H8DG6-F-0 Motherboard EATX
  • Silver Stone 550 Watt 80+ Platinum Power Supply
  • Roswell 4u Server Chassis